Skip to main content
XinmoJet

Technical Notes

How to Tell a Genuine HP45 Cartridge from a Rebuilt One

Rebuilt HP45 cartridges are sold as new all the time, and the difference shows up three weeks into a production run rather than on the invoice. Here is what actually distinguishes a genuine cartridge from a refilled or rebuilt one, and what you can check without a lab.

4 min readCartridge authenticityHP45Quality control

Why this matters more than the price difference

A rebuilt cartridge is an original body that has been opened, flushed, refilled and resealed. On a good day it prints. The problem is not that it prints badly on day one — it is that the things that fail are the things you cannot see: the filter mesh is partly clogged from the previous fill, the heater elements have already taken a few million firings, and the nozzle plate has been wiped against a cloth more times than it was designed for.

The failure mode is therefore not “it does not work”. It is “it works for two weeks and then one nozzle drops out in the middle of a shift”. By then the cartridge is in the bin and the supplier has a plausible story.

What you can check in five minutes, without equipment

The nozzle plate under a loupe. This is the single most reliable visual check. A genuine plate has clean, uniformly shaped orifices with sharp edges. A rebuilt one usually shows polishing marks, a slightly dulled surface, or residue around the orifice rims — the physical evidence of having been refilled and wiped.

The seal and the cap. Factory sealing is done by machine and is uniform. Hand-rebuilt cartridges are resealed by hand, and it shows in the adhesive line: uneven width, a lifted corner, or a different tape than the body’s original.

The ink meniscus and the colour. Look at the nozzle plate in good light. Genuine cartridges ship with a controlled meniscus. A cartridge that has been sitting refilled will often show a slightly proud or sunken meniscus, and the colour can be a shade off if a different formulation was used for the top-up.

The weight. A 42 ml industrial fill has a characteristic mass. A rebuilt cartridge that was “filled to full” by eye is usually lighter. This is crude, but a batch difference of a few grams across ten cartridges is worth taking seriously.

What you cannot check without taking a cartridge apart

The filter and the heater elements. These are sealed inside the body. A rebuilt cartridge typically reuses the original filter, which has already collected particles from the first fill. You will not see this from outside — you will see it as a gradual loss of nozzles over the following weeks.

This is why the honest answer to “how do I verify a cartridge” is: you verify it by running a batch and watching the nozzle count over time, not by looking at it. A supplier who offers to send a single sample cartridge for you to test is offering the only test that actually resolves the question.

The commercial tell

Rebuilt cartridges appear in the market at prices that are hard to explain. When a price is far below the level at which a genuine 42 ml industrial fill can be manufactured, shipped and supported, the difference is being paid for somewhere — usually in the filter and the heater elements, which is exactly where you cannot see it.

This is not an argument that all low prices are fraudulent. It is an argument that the price is not the information you need. Ask instead for the batch traceability and for printed samples from the batch you will actually receive.

What to ask a supplier before you commit

Send these four questions to any supplier, including us:

  1. Is the cartridge a new body with a new filter, or a reused body?
  2. Can you provide printed samples from the batch I will receive, on my substrate?
  3. What is the batch or lot identification, and how far back does it trace?
  4. If a nozzle drops out inside the first month, what is the replacement policy?

A supplier who answers all four in writing is a supplier you can run a trial with. A supplier who answers three and deflects the fourth has told you something useful.

Where to go next

If you are still selecting between widths, the difference between 12.7 mm and 25.4 mm has more effect on your code content than the brand of cartridge does. If your problem is that the code will not hold on the material at all, that is a substrate and ink question rather than a cartridge question. And if you want the ink options laid out side by side, start at the cartridge range.

The difference is easier to check than to describe: see how our TIJ ink cartridge factory is run covers the build, fill and test steps a rebuilt unit skips, and ink cartridge HS codes for your invoice matter once either one crosses a border.

If the question is what to find inside the cartridge, start above. If it is which supplier to judge, how to evaluate a TIJ cartridge manufacturer covers the questions to ask before the first order.

Want this confirmed on your own material?

We print on samples of your actual substrate and send them to you. Send the material, the line speed and the code content, and we will tell you honestly whether the fault is the ink, the surface or the line layout.