Technical Notes
DPI and Resolution in Thermal Inkjet: What the Number Actually Tells You
A 600 DPI printhead does not print 600 DPI codes, and a higher number is not automatically better for your application. Here is what DPI measures on a TIJ platform, how it relates to code legibility and scan rate, and how to read a supplier's resolution claim without being misled.
The number on the datasheet is a hardware property, not a print outcome
DPI — dots per inch — describes how densely the printhead can place ink droplets along the direction of travel. On a thermal inkjet platform it is fixed by the nozzle pitch inside the head, which is why a cartridge is described as “300 DPI native” rather than “300 DPI printing”.
This distinction matters because the number you care about is the resolution of the code that ends up on your product. That figure is a product of three things: the nozzle pitch, the speed at which the head crosses the substrate, and the fire frequency the controller can sustain. Change any one of them and the effective resolution changes, while the datasheet number stays where it was.
Why “up to 600 DPI” usually means “300 DPI, printed twice”
The most common way a thermal inkjet (TIJ) platform reaches a higher figure is not a finer printhead. It is interlacing: the controller fires the head on two passes with a half-pitch offset, so the second pass deposits droplets between the droplets of the first. The result is a code that looks denser and measures higher.
That is a legitimate technique — it is how the platform reaches 600 DPI. But it has a cost that the datasheet rarely states: the printing takes twice as long, or the head must travel at half the speed to fit both passes into the same physical distance. On a line running at a fixed speed, that shows up as a limit on how much content you can fit into the available print window. If you are printing a dense multi-line block plus a QR code, the interlaced resolution is often the thing that forces a layout change.
Resolution is not the same as legibility
There is a practical ceiling beyond which more resolution stops helping, and it is set by the substrate rather than the printhead. Thermal inkjet droplets spread when they land on a porous or low-energy surface. On an uncoated carton, a droplet that leaves the head at a known volume will have spread to a noticeably larger dot by the time it has been absorbed. Printing that surface at 600 DPI while the ink spreads to a 300 DPI footprint produces a darker mark, not a sharper one.
This is why the useful question is never “what is the resolution” but “what is the smallest feature that stays legible on my material”. On coated or non-porous stock, where the droplet does not spread, resolution maps closely to legibility. On absorbent stock it does not.
What actually governs whether a code scans
For a machine-readable code — QR, Data Matrix, barcode — the governing parameter is the module size: the width of a single black or white cell in millimetres. Every scanner has a minimum module size it will read reliably, and that minimum is what constrains the design, not the DPI figure.
A useful rule of thumb for a QR code is that module size should not go below roughly 0.25 mm for a typical industrial scanner, and it is worth being more conservative on a moving line where the scanner has less time to lock on. Working backwards from a minimum module size gives you the maximum amount of data you can fit into a given print width. That calculation is worth doing before choosing a cartridge, because it determines whether the 12.7 mm half-inch body can carry your content or whether you need the one-inch width.
How to read a resolution claim
Three questions separate a useful claim from a decorative one:
Native or achieved? The native figure is the nozzle pitch. The achieved figure is what the controller can deliver, usually through interlacing. Both are honest if they are labelled.
At what speed? A resolution figure without an associated print speed is not a specification. The two trade against each other directly on a TIJ platform.
On what substrate? A resolution figure measured on coated stock does not transfer to uncoated carton. If the claim does not say, assume it was measured on the easiest material available.
The short version
DPI is a property of the printhead. What lands on your product is a property of the printhead, the speed, the controller and the substrate together. Treat the datasheet number as a starting point for the conversation rather than an answer, and settle the question by testing on your own material — which is the only measurement that accounts for all four variables at once. If you want to see how the platform behaves across widths, the printer range covers both carriage sizes, and the cartridge range lists the ink systems those heads accept.
Resolution only means something against a real print, so date and batch coding on your line shows what changes at production speed, and see how our TIJ ink cartridge factory is run covers the 42 ml cartridges driving it.
Related reading
- 13 November 2026
How to Check TIJ Cartridge Compatibility Before Ordering
Most compatibility problems are information problems: the buyer sends a part number, the supplier answers the …
- 5 November 2026
Solvent vs Water-Based TIJ Ink: What Decides Which One You Need
Water and solvent are two carriers, and the carrier decides which surfaces an ink will wet, how long it takes …
- 1 November 2026
OEM Solvent TIJ Cartridges: A Private-Label Buyer's Guide
OEM for solvent TIJ cartridges is our tested cartridge with your label, carton and documentation. ODM adds ink…
Want this confirmed on your own material?
We print on samples of your actual substrate and send them to you. Send the material, the line speed and the code content, and we will tell you honestly whether the fault is the ink, the surface or the line layout.
